View MC100E212FN_741985.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
3 Bit Scannable Registered Address Driver
The MC10E/100E212 is a scannable registered ECL driver typically used as a fan-out memory address driver for ECL cache driving. In a VLSI array based CPU design, use of the E212 allows the user to conserve array output cell functionality and also output pins. The input shift register is designed with control logic which greatly facilitates its use in boundary scan applications.
MC10E212 MC100E212
3-BIT SCANNABLE REGISTERED ADDRESS DRIVER
* * * * * *
Scannable Version E112 Driver 1025ps Max. CLK to Output Dual Differential Outputs Master Reset Extended 100E VEE Range of - 4.2V to - 5.46V Internal 75k Input Pulldown Resistors
Pinout: 28-Lead PLCC (Top View)
SHIFT MR 25 LOAD CLK D2 VEE D1 D0 S-IN 26 27 28 1 2 3 4 5 6 7 8 9 10 24 NC S-OUTVCCO Q2b Q2a 23 22 21 20 19 18 17 16 15 14 13 12 11 Q2b Q2a VCC Q1b Q1a Q1b Q1a D2 D Q Q2a Q2b Q2b Q2a FN SUFFIX PLASTIC PACKAGE CASE 776-02
LOGIC DIAGRAM
S-OUT
NC VCCO Q0a Q0b Q0a Q0b VCCO * All VCC and VCCO pins are tied together on the die. D1 D Q Q1a Q1b Q1b Q1a
PIN NAMES
Pin D0 - D2 S-IN LOAD SHIFT CLK MR S-OUT Q[0:2]a, Q[0:2]b Q[0:2]a, Q[0:2]b Function Data Inputs Scan Input LOAD/HOLD Control Scan Control Clock Reset Scan Output True Outputs Inverting Outputs
D Q D0 S-IN LOAD SHIFT CLK MR
Q0b Q0a Q0a Q0b
12/93
(c) Motorola, Inc. 1996
2-1
REV 2
MC10E212 MC100E212
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol IIH IEE Characteristic Input HIGH Current Power Supply Current 10E 100E 80 80 min typ max 150 96 96 80 80 min 25C typ max 150 96 96 80 92 min 85C typ max 150 96 110 Unit A mA Condition
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol tPLH tPHL Characteristic Propagation Delay to Output CLK MR CLK to S-OUT Setup Time D SHIFT LOAD S-IN Hold Time D SHIFT LOAD S-IN Reset Recovery Within-Device Skew Within-Gate Skew Rise/Fall Times 20 - 80% 275 min 575 575 575 175 150 225 150 250 300 225 300 600 typ 800 800 800 25 - 50 50 - 50 25 100 0 100 350 100 50 425 650 275 max 1025 1025 1025 min 575 575 575 175 150 225 150 250 300 225 300 600 25C typ 800 800 800 25 - 50 50 - 50 25 100 0 100 350 100 50 425 650 275 max 1025 1025 1025 min 575 575 575 175 150 225 150 250 300 225 300 600 85C typ 800 800 800 25 - 50 50 - 50 ps 25 100 0 100 350 100 50 425 650 ps ps ps ps 1 2 max 1025 1025 1025 ps Unit ps Condition
ts
th
tRR tSKEW tSKEW tr tf
1. Within-device skew is defined as identical transitions on similar paths through a device. 2. Within-gate skew is defined as the difference in delays between various outputs of a gate when driven from the same input.
FUNCTION TABLE
LOAD L H X X SHIFT L L H X MR L L L H MODE Load Hold Shift Reset
MOTOROLA
2-2
ECLinPS and ECLinPS Lite DL140 -- Rev 4
MC10E212 MC100E212
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
0.007 (0.180) U T L -M
M
B -NY BRK
M
S
N
S S
0.007 (0.180)
T L -M
N
S
D Z -L-M-
W
28 1
D X VIEW D-D G1 0.010 (0.250)
S
V
T L -M
S
N
S
A Z R
0.007 (0.180) 0.007 (0.180)
M
T L -M T L -M
S
N N
S
H
S
0.007 (0.180)
M
T L -M
S
N
S
M
S
C
E G G1 0.010 (0.250)
S
K1 0.004 (0.100) J -TSEATING PLANE
K F VIEW S 0.007 (0.180)
M
VIEW S T L -M
S
T L -M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 -- 0.025 -- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 -- 0.020 2 10 0.410 0.430 0.040 --
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 -- 0.64 -- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 -- 0.50 2 10 10.42 10.92 1.02 --
ECLinPS and ECLinPS Lite DL140 -- Rev 4
2-3
MOTOROLA
MC10E212 MC100E212
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10E212/D*
MC10E212/D ECLinPS and ECLinPS Lite DL140 -- Rev 4

▲Up To Search▲

Price & Availability of MC100E212FN

	To Download MC100E212FN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .